產品明細

HMP2000

電源供應器

產品簡述

♦ 雙通道或三通道機種(HMP2020&2030)
♦ 最大輸出功率: 188W
♦ 每通道最大輸出電壓: 32V
♦ 每通道輸出最大功率: 80W (except HMP2020/ CH1:160W)
♦ 每通道輸出最大電流: 5A (except HMP2020/ CH1:10A)
♦ 電子保險絲(OCP), 過電壓保護(OVP), 過熱保護(OTP)

詢價

產品詳細介紹Product Introduction

Up to three channels in a single instrument

The R&S®HMP power supplies are primarily designed for industrial use. With two, three or four output channels and up to 10 A output current per channel, these rugged instruments are ideal for a wide variety of applications. They offer high efficiency with low residual ripple and many protection functions.
The R&S®HMP power supply family consists of four models. The R&S®HMP2020 two-channel power supply and the R&S®HMP2030 three-channel power supply deliver up to 188 W total output power, the three-channel R&S®HMP4030 and the four-channel R&S®HMP4040 offer a maximum output power of 384 W. The total load can be distributed as desired over the separate channels. Depending on the model, up to 80 W or 160 W of channel power is available – in any voltage/current distribution. Up to four galvanically isolated, floating output channels with overload and short-circuit protection are available, depending on the instrument type. The channels can be connected in series or parallel to obtain higher voltages or currents. The R&S®HMP4040, for example, offers a maximum voltage of 128 V or a maximum current of 40 A. All basic functions of the R&S®HMP power supplies are directly accessible on the front panel. The rotary knob plays a key role. It is used to set the voltage, current and limit values for the various protection functions.
The channel keys light up in different colors to indicate the operating conditions of the channels. All channels can be simultaneously switched on or off with the “Output” key, which lights up white when it is "on". Active outputs light up green in constant voltage mode and red in constant current mode. The R&S®HMP power supplies offer a variety of protection functions to prevent damage to the instrument and the DUT. You can separately set the maximum current (electronic fuse, overcurrent protection/OCP) or the maximum voltage (overvoltage protection/OVP) for each channel. The output channels switch off when either of their set limits is reached. Overtemperature protection (OTP) prevents the instrument from overheating. In industrial applications, power supplies are often installed in 19-inch racks. The R&S®HZ42 and R&S®HZP91 rack adapters are available for this purpose. Additional connections for all channels (including sense lines) are provided on the rear panel to simplify use in system cabinets. The R&S®HMP power supplies are equipped with a dual USB/LAN interface as standard. This interface can optionally be replaced by a dual RS-232/USB interface or a GPIB (IEEE488) interface.

Available models
Models	Number of output channels	Max. output power	Output voltage per channel	Output current per channel
R&S®HMP2020	2	188 W	0 V to 32 V	channel 1: 10 A, channel 2: 5 A
R&S®HMP2030	3	188 W	0 V to 32 V	5 A

Features

R&S®HMP2020/HMP2030 with 2/3 channels and 188 W total output power
R&S®HMP4030/HMP4040 with 3/4 channels and 384 W total output power
Maximum output voltage of 32 V per channel; higher voltages possible in serial operation
High output currents up to 5 A/10 A (depending on the model); higher currents possible in parallel operation
Linear postregulation for low residual ripple
Electronic fuse (OCP), adjustable maximum voltage (OVP), overtemperature protection (OTP)
Dual USB/LAN interface as standard; RS-232/USB or GPIB (IEEE488) optional
Rear panel connections, including sense lines, for all channels

More than meets your daily needs
- All channels galvanically isolated and floating
- All channels have the same voltage range
- All channels have overload and short-circuit protection
- Parallel and serial operation
- Constant voltage and constant current modes
- Tracking and link functions
- Protection functions to safeguard instrument and DUT
- Modern instrument concept: small, compact and quiet

Easy operation
- Intuitive to use
- Color coding of operating states
- EasyArb function for all channels
- Save and recall instrument settings

Ideal for labs and test systems
- Tailored for use in labs and system racks
- Sense function for more stringent accuracy requirements
- Remote control of instrument functions

Specifications
All data is valid at 23°C (–3°C/+7°C) after 30 minutes warm-up time.

Electrical specifications
Outputs	All channel outputs are galvanically isolated and not connected to ground.
Number of output channels	R&S®HMP2020	2
	R&S®HMP2030	3
	R&S®HMP4030	3
	R&S®HMP4040	4
Total output power	R&S®HMP2020/HMP2030	max. 188 W
	R&S®HMP4030/HMP4040	max. 384 W
Maximum output power per channel	R&S®HMP2020	channel 1: 160 W; channel 2: 80 W
	R&S®HMP2030	80 W
	R&S®HMP4030/HMP4040	160 W
Output voltage per channel	all models	0 V to 32 V
Maximum output current per channel	R&S®HMP2020	channel 1: 10 A; channel 2: 5 A
	R&S®HMP2030	5 A
	R&S®HMP4030/HMP4040	10 A
Maximum voltage in serial operation	R&S®HMP2020	64 V
	R&S®HMP2030/HMP4030	96 V
	R&S®HMP4040	128 V
Maximum current in parallel operation	R&S®HMP2020/HMP2030	15 A
	R&S®HMP4030	30 A
	R&S®HMP4040	40 A
Voltage ripple	3 Hz to 100 kHz	< 250 μV (RMS), typ. <150 μV (RMS)
	3 Hz to 20 MHz	typ. < 1.5 mV (RMS)
Current ripple		< 1 mA (RMS)
Load regulation	load change from 10% to 90%
Voltage	±(% of output + offset)	< 0.01 % + 2 mV
Current	±(% of output + offset)	< 0.01 % + 250 μA
Load recovery time	to within ± 10 mV of the set nominal voltage	< 1 ms
Line regulation	±10% change in mains voltage
Voltage	±(% of output + offset)	< 0.01% + 2 mV
Current	±(% of output + offset)	< 0.01% + 250 μA
Programming resolution
Voltage		1 mV
Current	R&S®HMP2020 channel 1 (10 A)	< 1 A: 0.2 mA; ≥ 1 A: 1 mA
	R&S®HMP2020 channel 2 (5 A)	< 1 A: 0.1 mA; ≥ 1 A: 1 mA
	R&S®HMP2030	< 1 A: 0.1 mA; ≥ 1 A: 1 mA
	R&S®HMP4030/HMP4040	< 1 A: 0.2 mA; ≥ 1 A: 1 mA
Programming accuracy
Voltage	±(% of output + offset)	< 0.05% + 5 mV
Current	±(% of output + offset)	< 0.1% + 5 mA
Output measurements
Measurement functions		voltage, current
Readback resolution
Voltage		1 mV
Current	R&S®HMP2020 channel 1 (10 A)	< 1 A: 0.2 mA; ≥ 1 A: 1 mA
	R&S®HMP2020 channel 2 (5 A)	< 1 A: 0.1 mA; ≥ 1 A: 1 m
	R&S®HMP2030	< 1 A: 0.1 mA; ≥ 1 A: 1 mA
	R&S®HMP4030/HMP4040	< 1 A: 0.2 mA; ≥ 1 A: 1 mA
Readback accuracy
Voltage	±(% of output + offset)	< 0.05% + 5 mV
Current	±(% of output + offset)	< 0.1% + 2 mA
Output measurements
Temperature coefficient (per °C)	5°C to 20°C and 30°C to 40°C
Voltage	±(% of output + offset)	0.01% + 2 mV
Current	±(% of output + offset)	0.02% + 3 mA
Sense function		yes, for each channel
Maximum sense compensation		1 V
Ratings
Maximum voltage to earth		150 V (peak)
Maximum counter-voltage	voltage with same polarity connected to the outputs	33 V
Maximum reverse voltage	voltage with opposite polarity connected to the outputs	0.4 V
Maximum reverse current	for 5 minutes max.	5 A
Remote control mode
Command processing time		< 50 ms
Protection functions
Overvoltage protection		configurable for each channel
Overcurrent protection (electronic fuse)		configurable for each channel
Response time	(I_load > I_response × 2)	< 10 ms
Fuse linking (FuseLink function)		yes
Fuse delay time	configurable for each channel	0 ms to 250 ms (10 ms increments)
Overtemperature protection		yes
Special functions
Arbitrary function (EasyArb)
Parameter		voltage, current, time
Maximum number of points		128
Dwell time		10 ms to 60 s
Repetition		continuous or burst mode 1 to 255 repetitions
Data memory		non-volatile memory for three arbitrary functions and ten instrument settings
Display and interfaces
Display	R&S®HMP2020/HMP2030	240 pixel × 64 pixel LCD
	R&S®HMP4030/HMP4040	240 pixel × 128 pixel LCD
Front panel connections	channel outputs	4 mm safety sockets
Rear panel connections		connector block with 4 lines per channel
Remote control interfaces	standard	dual interface LAN/USB
	optional	dual interface USB/RS-232 (R&S®HO720)
	optional	IEEE488 (GPIB) (R&S®HO740)
General data
Environmental conditions
Temperature	operating temperature range	+5°C to +40°C
	storage temperature range	–20°C to +70°C
Humidity	noncondensing	5% to 80%
Power rating
Mains nominal voltage		115 V/230 V (±10%); CAT II
Mains frequency		50 Hz to 60 Hz
Maximum power consumption	R&S®HMP2020/HMP2030	300 W
	R&S®HMP4030/HMP4040	600 W
Mains fuses (115 V power source)	R&S®HMP2020/HMP2030	2 × T6.3H/250 V
	R&S®HMP4030/HMP4040	2 × T10H/250 V
Mains fuses (230 V power source)	R&S®HMP2020/HMP2030	2 × T3.15H/250 V
	R&S®HMP4030/HMP4040	2 × T5H/250 V
Product conformity
Electromagnetic compatibility	EU: in line with EU EMC Directive 2014/30/EU in line with EU EMC Directive 2014/53/EU	applied harmonized standards: ❙ EN61326-1: 2013 ❙ EN61326-2-1: 2013 ❙ EN55011: 2016 (Class A) ❙ IEC61000-3-2 2014 (Class B) ❙ IEC61000-3-3: 2013 ❙ EN50581:2012 (RoHS) ❙ EN300 328 V2.1.1
	Korea	❙ KN61000-4-11: 2008
Electrical safety	EU: in line with Low Voltage Directive 2006/95/EC	applied harmonized standards: EN61010-1:2010
	USA, Canada	CSA C22.2 No. 61010-1:2012
Mechanical resistance
Vibration	sinusoidal	5 Hz to 55 Hz, 0.3 mm amplitude const., 55 Hz to 155 Hz, 0.5 g const., in line with EN 60068-2-6: 2008
	random	8 Hz to 500 Hz, 1.2 g (RMS), in all 3 axes, in line with EN60068-2-64: 2008
Mechanical data
Dimensions (W × H × D)	R&S®HMP2020/HMP2030	285 mm × 95 mm × 405 mm (11.22 in × 3.74 in × 15.94 in)
	R&S®HMP4030/HMP4040	285 mm × 136 mm × 405 mm (11.22 in × 5.35 in × 15.94 in)
Weight	R&S®HMP2020	7.8 kg (17.2 lb)
	R&S®HMP2030	8.0 kg (17.6 lb)
	R&S®HMP4030	12.4 kg (27.3 lb)
	R&S®HMP4040	12.8 kg (28.2 lb)
Rack installation	R&S®HMP2020/HMP2030	R&S®HZ42 option
	R&S®HMP4030/HMP4040	R&S®HZP91 option
Recommended calibration interval	operation 40 h/week over entire range of specified environmental conditions	1 year